How To Measure Rim Bolt Pattern 5 Lug

For 5 lug wheels its only slightly more complicated then the 4, 6, or 8 lug measurement. Bolt patterns can be measured in inches and millimeters using two number system.

Pin on Wheels

If you need the 4, 6 or 9 lug page look here how to measure 4, 6 or 8 lug wheel bolt pattern

How to measure rim bolt pattern 5 lug. Measure from the center of one bolt to the center of the bolt across from it and multiply by 1.05 or measure from the center of one bolt to the back side of the bolt across from it. Typically this will be 4, 5, 6, or 8. The easiest way to estimate the 5 lug bolt pattern, is to measure from the back of a hole to the center of the second hole.

I am including a picture that will show where to measure. These methods will get you very close to your bolt pattern. This will get you the same measurement.

Remove the existing wheel (the rear wheel is usually the easiest to measure because the hub normally won’t be in the way). A 8 lug bolt pattern or pitch circle diameter (pcd) is made up of the stud count (8) and the bolt circle measurement, the notional circle determined by the center position of the studs. The diagram above should make it clear.

A bolt circle of 5 x 4.5 would indicate a 5 lug bolt pattern on a circle with a diameter of 4.5 inches. There's an easy way to measure and be sure though. Common bolt patterns are 4, 5, 6, or 8 lug holes.

For a 4 lug wheel, measure center to center of two holes directly across from each other. That should get you your bolt pattern measurement. Now, start at the outer wall of the bolt hole and measure all the way to the center of the other bolt hole.

If there are 5 studs, multiply the measurement by 1.05 to get the bolt pattern diameter. I am including a link to a video that will also show you how to measure a bolt pattern. Where the first number shows the holes in the wheel whereas the second shows the diameter.

Remember that you always measure the lug pattern or bolt pattern for your factory original wheels from the center of the lug hole to center of the one across from it (not edge to edge). Measure center to center of two holes directly across from each other. To measure 5 lug pattern wheels, hold the end of the ruler or tape measure to the center of one bolt.

You can also determine your 5 bolt pattern by measuring the distance between the center of one bolt hole, to the center of the bolt hole next to it. This is the way to measure the bolt pattern on your vehicle if it is not a 5 lug (so 4 lug, 6 lug and 8 lug all need to be measured this way): Take a look at our diagram for an illustration of how it is measured.

To determine the bolt pattern on a 5 lug wheel, measure from the center of a wheel stud to the outer edge of the stud furthest away from it. The first step in determining your wheel bolt pattern is counting how many bolts (or lugs) your wheel has. Identifying your bolt pattern or lug pattern.

For example, a rim with 5×100 indicates five lug pattern on the circle with diameter 100 mm. You can choose basically any hole to start with, but, you have to. Bolt patterns with an even number of lugs are measured from bolt center to bolt center while 5 lug bolt patterns are measured from the top of the upper lug to the center of the lower lug.

In a decimal that’s 6.125. To find your bolt pattern, measure the distance as accurately as possible and then find the corresponding bolt pattern in the conversion table below. Or the way i prefer is to measure from the center of a bolt hole to the outside edge of either of the bolt holes furthest from it.

Next, you'll measure how many inches apart the bolt holes are. Measure 8 lug wheel bolt patterns from center to center distance between two studs that are across the hub from. To measure the rim bolt pattern on a wheel with 5 bolt holes, hold the tape measure on the edge of a bolt hole and measure across to the center of the 2nd hole.

When it comes to 6 bolt rim, the measurement process is also easy. How to measure 8 lug bolt patterns. You need to measure from the center of one lug to the center of the lug nearest to it.

If there are 7 studs, multiply the measurement by 1.03. If it measures 3 inches the bolt pattern would be 5 on 5. Now that you know how to measure lug bolt patterns, here is a.

Select 2 bolts that have a 1 bolt spacing on either side. Measuring 5 lug bolt patterns. The diagrams below indicate the proper measuring methods.

A common measurement for a 5 bolt pattern is 120 millimetres (4.7 in) from the top of 1 lug to the center of another. So, you have to measure from the center of one hole and end up to the center of the opposite hole. Wheel dimensions there are four important measurements that are used to categorize and identify a wheel for fitment purposes.

Because of the multiplication involved, it’s easier to measure 5 or 7 stud bolt patterns in millimeters. Determining your trailer wheel bolt pattern. If you don’t have the template handy, you measure from the center of any hole, skip a hole in either direction and then measure to the outside edge of that hole.

It basically goes the same as the 4 bolt rim. Extend the ruler directly across from the bolt to the space across from the bolt, located in the center of two bolts or lugs, to determine the measurement. You measure from the back of one lug (skip to next lug as shown) and to the center of that lug.

If you’re measuring a 5 bolt pattern, make sure that you skip the adjacent bolt and measure. You get a measurement of 6 1/8″.

Fuel Wheels STRYKR Gloss Black Milled 6Lug Wheel 20x9