What Is The Best Way To Cut Cast Iron Pipe

Luckily cast iron pipes are fairly brittle so it should break easily. It’s nearly impossible to break a cobalt steel twist bit on cast iron.

Pin on Bathroom Redo!

George vondriska shows how to cut a threaded through or blind hole in cast iron with a center punch, drill, tap and die set, a little oil drill and an all important back and forth motion.

What is the best way to cut cast iron pipe. A sthil saw with a 300mm blade might nearly do it. It has 2 toilets and a sink and shower that drain into it. It is likely gray cast iron which cuts easily with a hacksaw or circular saw , or reciprocating saw, much easier than steel.

Grip the drill firmly while you use it. Dont forget the safety glasses and dust mask. Within 10 minutes, the putty will harden, sealing the pipe.

Best way to cut off a 100 year old cast iron pipe i'm fixing my second floor bathroom, and when i opened up the wall, i discovered that the plumbing stack has a massive crack in it. The traditional method used most of the time to clean cast iron pipes is a drain snake with cable and blades. Vertical runs of pipe need a riser clamp at every floor level.

Other than in the attic, it is contained in a wall. Not likely to be white iron. Rotate the pipe, hammering around the circumference until the pipe breaks.

As the epoxy putty completes mixing, the two contrasting colours will blend into a cast iron colour. Chain cutters are for cast iron pipe and not much else since they rely on the brittleness of the pipe to do their work. Drill a hole in the cast iron pipe.

(standard hacksaw blade, start with 18 tooth ). Threaded holes in cast iron machine tables are just the solution you need for holding jigs and fixtures. Nodular and malleable cast irons are tougher , but still easier to cut than steel.

Actually, the crack is so large you could call it a hole about two feet tall, and 1/3 the width of the pipe. Also the fumes from pvc can kill you before a fire does. This method is great when you have a clog, but we’re talking about descaling the inner walls of the old cast iron pipes to get them back to their original state of flow capacity.

You simply cut off the required amount of epoxy putty from the stick and knead it by hand. You can even take it a step further by getting a drill bit that’s coated with titanium nitride to resist heat and friction. If you don’t keep it steady in the cut the blade will destructively disintegrate with a loud bang.

Johnpost april 13, 2013, 4:06pm #9. The abrasive blade in a circular saw works well. The plastic makes much more noise than cast iron.

With chalk draw a line around the pipe where you want to cut it, put the edge of the chisel on the line and hammer the end of it. Added to that, making a repair means we have to cut out a piece of the pipe that is leaking and replace that section with pvc pipe. This is primarily noticed in walls where the upper floors drain vertically to lower floors.

You then apply the epoxy putty by pushing it into the hole or crack in the pipe. This will involve cutting the floor and removing the entire cast iron pipe where it currently runs under the floor and replacing it. Even if the cast isn’t hot, the friction will build heat quickly.

If the cuts you make will leave a long section of pipe unsupported, install pipe hangers or riser clamps on both sides of the section you will cut. When cutting cast iron pipe, i used a lenox 9 inch diamond recip saw blade that has tangs on both ends, so you can switch ends when one section gets dull. Put on the goggles and gloves.

Cut iron pipe with a hammer and chisel this is a very good way to cut iron pipe. Bath tubs, plumbing pipes and skillets are a few of the products manufactured with cast iron. I don’t own a “pipe snapper” to cut cast iron.

Squeeze the saw's trigger and slowly lower the moving blade onto the line at one end of the section of cast iron; I have a 4 inch cast iron drain pipe that is in the wall and runs into the floor in the basement. Cast iron's strength and reduced frictional wearing allow these and other products to have a long life.

Breaking cast iron creates smaller pieces of material to move and throw away. Either of these substances will cut right through the metal without becoming dull too quickly. An angle grinder with a metal blade will cut most of it, you need access all around the pipe.

The reciprocating saw allows you to cut straight through the pipe the way that you would cut butter with a butter knife. So my favorite tool for that nasty job is a grinder equipped with a diamond blade. Spread the handles of the cutter apart and hook the chain into the notch on the free handle.

Cast iron in it pure state is called grey cast or pig iron and in bygon times was used to tip cutting tool because it is one of the hardest metals they had.normaly cast iron is very easy to cut and drill as the carbon acts like wax ,but if the iron as been chilled when made or quenched in water it reverts back to gray cast iron.ps this also happens when casting thin pipes like drain pipes. It is from just above the basement floor (built into a side wall) and runs all the way through the roof for vent. So with that mind, it’s more than likely any system made of cast iron will need to be replaced in the next five to 20 years (closer to five than 20, by the way).

Create a marking line and use the hammer and chisel to score the line around the pipe. Connect the electric drill to the drill bit. If you don’t have a crawl space and you can’t do the reroute option then your next best choice is to replace the cast iron pipes in the existing locations.

I need to replace the pipe with pvc.

Pin on Home Improvement