How To Clean A Deer Mount

We went with the base to get a clean bleached finish on the entire skull yet a natural age and rustic patina throughout the full antlers for a nice contrast. A colony of beetles will clean every scrap of meat and tissue off bone in very little time.

Classic Antler Mounts Taxidermy, Moose skull, Taxidermy

Lay the skull cap in a plastic pan with the antlers facing up.

How to clean a deer mount. Maceration is the process of placing the skull into a bucket of warm water and allowing the bacteria to decompose or digest the flesh off the skull. Process takes about 3 weeks (that’s not much of a con). Tested and preferred products like seybrite trophy cleaning kits, show groom and protex mount care.

Take the razor blade or knife and scrape the antlers to clean it. A smaller wire brush will help you get into the nooks and crannies more easily, but a wire brush from your grill will work. Dip the tip of a cotton swab into the rubbing alcohol.

Don’t get to much water covering the antlers because it may discolor them. Fill a large pot of water; This will remove any remaining hair or organic matter.

Dry the antlers with a clean, dry cloth. Bring an old mount back to life! It is probably the most gentle process by which it can be done, but the time and effort to.

Clean your prized taxidermy trophies with a soft cloth misted with 409® cleaner. By forming a dirt and. Only use a damp sponge to clean.

Allow them to boil for 30 minutes to remove any bacteria. If you soak the deer head with a wet sponge, it may affect the appearance and/or cause damage. And if you are going to be out of town for a long period of time, cover each trophy with a clean sheet to keep dust from piling up.

To dry dust the head mount, wipe it periodically with a microfiber cloth. Rub the salt thoroughly into the underside of the skull cap. Add one scoop of oxiclean into the water, this will act as a degreaser.

We start by painting on a generous amount of the skull whitening paste, starting on the back of the skull and working forward. Use the knife and screwdriver to cut and peel away any flesh attached to the underside of the skull cap. How do you clean old deer mounts?

• clean inside the mouth: Only use a damp sponge to clean. To dry dust the head mount, wipe it.

Dry hair and brings back. Fill a small bowl with rubbing alcohol. Continue rubbing until the eyes are clean and clear.

Always go with the direction of the coat whether using a vacuum or feather duster in an up and down motion over the entire length of the mount whether it is a full body or shoulder mount. Create a solution mix three drops of dish soap in a bucket with warm water, agitating it to create a sudsy solution. Scrub the antlers thoroughly with a wire brush.

And the results are amazing! Discard any remaining skin from the antlers. The naturalbeauty of the mount.

Do not spray the 409® directly onto the mount itself. The mouth of any trophy speaks volumes about the animal and shouldn’t be neglected during cleaning. Wipe the deer mount with vinegar solution once you have wiped down the fur and horns of the deer mount, deodorize it in order to do away with possible unwanted odors that developed as a result of the soapy solution and dust particles.

In this two part tutorial, learn how to deflesh the skull and antlers of a deer and make it into what is commonly known as a dry skull, desert, european, texas, or western mount. Once your antlers are clean, allow them to air dry in the sun for a day. Be sure to dust your mounts regularly to avoid excessive dust buildup.

If your mount is in a controlled area — free from moisture, heat and sunlight — you can clean your mount about once a month. Maceration is the process of placing the deer skull in warm water until it softens and the bacteria decomposes and digests the flesh. Scrape all the flesh off until the bone is clean.

If your trophy is in a high dust area, clean it twice per month. Remove surface dirt and debris from the antlers with a damp cloth. After giving them a good scrub, fill a large pot with water and a pinch of salt, bring it to a boil, and submerge the antlers.

Dip a clean wash cloth into vinegar and use it to wipe down the deer’s fur in the hair’s growing direction. It should be big enough to completely submerge the deer’s skull. This is the easiest and most gentle process to clean a deer skull.

If you soak the deer head with a wet sponge, it may affect the appearance and/or cause damage. Always work with the lay of the hair, not against it. Pour salt on the skull portion.

Stain shield over the entire mount. Rub the deer's eyes with the cotton swab in a gentle, circular motion. Allow the antlers to dry in a location where they will not be disturbed for 24 hours.

You want to clean off the head as best as possible, removing all excess meat To learn how to perform regular maintenance on your deer antlers,. If you’re just cleaning a skull cap, i would consider this overkill, but if you want to clean an entire deer skull for a european mount (euro mount), this is a great way to go.

Apply white primer to the antlers using a small paintbrush. You need to get rid of any remaining skin or velvet on the deer’s antlers and you can do this with help of a razor blade or a small knife. There’s no way of knowing ahead of time whether the suction will cause damage to the mount.

Use a soft bristled brush to fix hair that is out of place after the cleaning.

Antler Mount Kit Traditions Deer in 2020 Antler mount