How To Build A Still Out Of A Keg

Moonshine has been around for a long time and there are many types of stills today as the designs have evolved over time. 2 remove the central tube from the keg

Home made, DIY, moonshine still Another keg setup with a

The kit made installing and removing the column from the keg a snap.

How to build a still out of a keg. Use a reciprocating saw and a metal blade to cut around the side of the cap. A link to a set of youtube videos will be emailed to you after purchase. And many other areas of the world, you will most likely be breaking the law.

Below is a collection of reflux and pot still plans that are great for anyone looking to build their own still. This will mark the center point of the pipe. How to build a moonshine still from a beer keg, top tutorial, how to build a moonshine still from a beer keg

Oh, let's not forget the mash. That was running quite slow too Today we have a multitude of designs including.

This is called an easy flange we need to bend over the edges of the pipe by about 6mm so they are at a 90 degree angle to the pipe but you can't do this all in one go it. Fill the column with mesh and it will become a small reflux kit. The fire, the pot, the condenser and something to collect it in.

For this you will need a hammer and an anvil or something to hit the copper against. I was previously using a homemade setup that was inefficient and a royal pain in the butt. One board for the whole collar supplies.

Just contact us for more details. The spear is the stainless steel tube. Place a bag of botanicals in the top bend it becomes a gin still.

The pieces were all high quality. Additionally you can use a still to brew your petrol fuel for your motorized contraption. To build the assembly you'll use the spear from the tap valve you removed at the beginning.

The proof of the alcohol steam is doubled at this point. To build the column body follow these steps : After many requests, we are now offering self build diy moonshine still kits for the adventurous enthusiast.

First off run your vinegar mix, make sure you have enough to cover the element and then a few more inches above it, you need to run your boiler at full power until the column temp reaches 40 degrees c then reduce it to half power and turn the water on to your condenser coil, make sure the needle valve on the out let is open and a bucket is under the take off pipe. Ok what we need to do is cut a section of 54mm copper pipe about 30 cm in length and then make a flange on the end so it can attach to the keg. You need to cut it to length so that it extends from the center of the keg where you drill the 3/4 hole to the edge of the keg.

Normal build times for the novice will be. Alcohol still variations cater to the type of moonshine creation you are trying to create. Add another 50cm section and you have a full height reflux column.

The videos show you how to complete the entire homemade still kit process. If your going to build a still take some pictures or make a video while your making it. The first challenge was to find a scale thin enough to place under the keg and still fit in the kegerator that was sturdy enough not to bend under the weight of a 150lb keg.

It warmed up too much before i was able to get all the tails. I tried multiple designs and methods to reinforce the scale, but they were either unstable or added too much thickness that ultimately put pressure on the top tubes. I used some reclaimed lumber for this build not because of style (although i do like the way the end product looks) but more to pinch pennies.

We’ll pay you to make a how to guide for your still build! The thump keg is named after the thumping sound that is made from the steam being forced under the level of alcohol in the barrel. Basically this is a pot still kit.

Various forms of alcohol include whisky, bourbon, scotch, vodka, gin, rum, and many more tasty liquor spirits. 5cm x 25cm x 4 meter board (1) *equivalent 2″x 10″x 13′ And while it is hoped that the still will be used for legitimate purposes, always keep in mind that if you decide to build and use the still to produce ethyl alcohol then, in the u.s.

Getting something fairly straight will make life easier when constructing the collar. It started with a simple pot still that has 4 components: Because the top of the keg is domed, the washers were bent almost in half to compensate for the drop in elevation on each side of the bolt.

Once the column reach's about 91.3 degrees you will start to see water coming out. To allow fitting the still column to the keg cover, an adapter is made from a 2 automobile exhaust flange and a 2 copper coupling and bolted to the bottom of the bowl. The keg to column kit was an awesome upgrade to my still.

Drill a hole in the top of the keg near the tapping cap.

Build a Keg Still for Whiskey (Pot Still Design) Wine